Profiled sheeting C-8 standard lines

Automatic roll decoiler - RS-7M (Driven, cantilevered)

Type - Cantilever with attachable support, with manual blades spreading tool
Weight - 1050 kg
Load capacity - 7000 kg
The decoiler blades spreading mode - Manual by the screw drive
Spreading stroke limit - 480-610 mm
Decoiler drive type - Asynchronous, frequency-controlled by Vesper inverter
Decoiler drive power - 7.5 kW
Metal decoiling speed - 50 m/min
Width of the coil (blanks) - 1250+7 mm
Coil inner diameter - 480-600 mm
Coil outer diameter - 1500 mm
Operating mode - automatic
Loop Tracking - Extension Rod
Emergency sensor for disconnecting the line when the loop is pulled - Limit switch
Overall dimensions (LxBxH) - 2300x1160x1700 mm
Possibility of reverse rotation - provided
The number of the decoiler trunk blades - 3

COLD ROLL-FORMING MILL С8

Coil loading mode - manual
Operation area width - 1250 mm
Metal thickness processed - 0.4-0.7 mm
Guide table - adjustable, with three idle input rolls
Productivity - 32 m./min
Drive type - Asynchronous, frequency-controlled
Installed power of the motor gear - 7.5 kW
Drive rolls position - all bottom
Roll drive type – chain
Roll diameter - 92 mm
Profile length accuracy - ± 1-2 mm
Number of stands - 18 pcs
Band motion sensor - circular pulse encoder "LIR"
Control type - programmable controller
Forming rollers material - Steel 40H GOST 4543-2016 with heat-treatment
Overall dimensions (LxBxH) - 9000x1680x1750 mm
Weight - 5 000 kg
Rope-Stop, with Stop button – Emergency type
Push-button station for loading operation modes on the guide table – 1 pc
Guillotine Unit type - profile electromechanical
Installed power – over 2.2 kW
Material of guillotine blades - ChVG, Ch12М Hardening 57…60 HRC

ACS (automated control system)

Quest archive - unlimited
Operating modes
Manual - Operation of actuators by pressing buttons
Semi-automatic - Operation of the guillotine drive by pressing a button, the rest in automatic mode
Automatic - Operation of actuators according to the controller program
Material change mode - Line stop and metal cut for waste-free material change
Stamping step adjustment - 350,400,450 mm as default
Emergency mode - Line stop without resetting the program in case of failure or malfunction of the decoiler, sheet piler or guillotine
Total counter of all rolled metal
Finished sheets cut-off accuracy - ±1-2 mm
Number of programmable positions (quantity by length) - 16 pcs
Control panel - Touch 10", multifunctional "Delta Electronics"
Electrical cabinet - RITTAL
Controller and frequency drives - «Delta Electronics»

Automatic Finished Sheet Piler

Sheet Piler Control System – Programmable Controller
Pick-up feeder drive "SITI" - 2.2 kW
Operating mode - Automatic
Manual - push-button
Sensors for tracking the position of the pick-up feeder - Non-contact inductive
Sheet piler length - 6 r.m.
Receiving carts - Roll-out of the cart to the side (forward along the rolling direction)

COST OF THE EQUIPMENT SET:

Profiled sheeting lines С-8 option - on request

It is possible to manufacture a complete set with rollers without heat treatment and a capacity of 22 r.m./min.

ROLL-FORMING EQUIPMENT:
LSTS, The metal tiles production lines, Profiled sheeting, Metal siding line, Seam roof. Folding machine

C-8 lines

Profiled sheeting C-8 standard lines

COST OF THE EQUIPMENT SET:

Moscow region, Krasnogorsk, Pavshinsky Boulevard, 17	Contacts
		Fl22-design studio

ROLL-FORMING EQUIPMENT:LSTS, The metal tiles production lines, Profiled sheeting, Metal siding line, Seam roof. Folding machine

C-8 lines

Profiled sheeting C-8 standard lines

COST OF THE EQUIPMENT SET:

ROLL-FORMING EQUIPMENT:
LSTS, The metal tiles production lines, Profiled sheeting, Metal siding line, Seam roof. Folding machine